Browse Wishlist
SKU: KG70 Categories: ,
Share this product


MODEL#/ SKU:Series NameKick PointBalance PointTypeFlex CodeFlex (Equivalent)Torque ±0.5°Tip Dia. ±0.05mmTip/Pal ±0.5″Butt Dia. ±0.12mmButt/Pal ±0.5″Length ±0.1″Weight ±2gFrequency ±5cpmMaterials
KG70-D50KEVLAR BALLISTIC DRMID54.00%STD DRD502X4.3°8.50mm3.00″16.10mm6.00″46″73g290cpm40T.30T, Kevlar, 3K Fiber
KG70-D40KEVLAR BALLISTIC DRMID53.00%STD DRD40X4.5°8.50mm3.00″15.80mm6.00″46″70g270cpm40T.30T, Kevlar, 3K Fiber
KG70-D30KEVLAR BALLISTIC DRMID51.00%STD DRD30S4.7°8.50mm3.00″15.70mm6.00″46″66g255cpm40T.30T, Kevlar, 3K Fiber
KG70-D20KEVLAR BALLISTIC DRMID51.00%STD DRD20R4.7°8.50mm3.00″15.50mm6.00″46″65g240cpm40T.30T, Kevlar, 3K Fiber
KG70-D10KEVLAR BALLISTIC DRMID49.00%STD DRD10A5.0°8.50mm3.00″15.30mm6.00″46″58g215cpm40T.30T, Kevlar, 3K Fiber

1. FREQUENCY Measurement Array Parameters: 4.5″ clamp as follows:

ShaftClub LengthHead Mass Estimate:Shaft LengthChuck WT.Insert Depth
Driver45.00″+/-1.50″200g +/-5g46.00″205g1.00″


MODEL#/ SKU:Flex Code (FLEX)Low RangeDRIVER SwingSpeed Fit Baseline +/- 8MPHHigh Range
KG70-D50D50 (2X)117mph125mph133mph
KG70-D20D20 (R)82mph90mph98mph

Elastically Tailored Composites

Wound for an explosive transfer of kinetic energy….
however you drive it, KINETIXX® IMRT will optimize down range distance and target performance.

An active shaft that increases in frequency the greater the force applied.

This hard kicking, elastically tailored composite is engineered to improve club forgiveness and

generate outrageous ball speed and precise shot control!


Filament wound Vacuum Cured Construction technology produces round, pre-loaded concentric and spineless golf shafts for incomparable stability, dynamic response and feedback.

Fitting the widest array of players and swing types. Each shaft profile and flex present a visible, pre-loaded fiber architecture.

Tension tailored for torsional recovery and attenuation of vibration, for the purest kinetic energy transfer from shaft to clubhead.

PADERSON® KINETIXX® loaded kevlar BALLISTIC series features the worlds only continuous fiber filament wound kevlar construction technology.

Optimizing the extraordinary advanced composite material properties producing shafts with an incredibly high tensile strength-to-weight ratio, 5x stronger than steel, with 20x the elastic strength.

KG70-D is a Mid-Balance, Mid-Kick point advanced composite shaft pre-loaded with a visible fiber structural grid Engineered according to each flex, delivering balanced strength from butt to tip, producing medium-high Ballistic trajectory with exceptional stability and feel.

Installation Guidelines

Installation Guidelines PADERSON KINETIXX LOADED shafts:

Installation should only be completed by a qualified, trained club builder.

  1. All PADERSON KINETIXx loaded shafts are to be BUTT Cut to length only.
  2. Do not TIP trim any shaft model! Regardless of CPM, or club assembly config.
  3. Please do not Chamfer the tips however light belt abrasion is recommended.
    *Tip preparation: light belt abrasion or hand sanding recommended prior to final assembly.
    *To ensure a smooth and clean build, we perform a post-production tip preparation: 1″ Metalwoods, 1.25″ Irons. depending on hosel bore depth, there will in many assemblies be the need to lightly sand beyond the prepared surface delivered. Light belt abrasion is also recommended to insure a full shaft insert and adequate epoxy adhesion. Do not Chamfer tip section or blade prep (scratch) tip to prepare for epoxy.