LAUNCH TP

$274.99

Clear
SKU: KGTP65+ Categories: ,
Share this product

Description

SPEC DECK
MODEL#/ SKU:Series NameKick PointBalance PointTypeFlex CodeFlex (Equivalent)Torque ±0.5°Tip Dia. ±0.05mmTip/Pal ±0.5″Butt Dia. ±0.12mmButt/Pal ±0.5″Length ±0.1″Weight ±2gFrequency ±5cpmMaterials
KGTP65+ D50KEVLAR LAUNCH TP DRLOW57.00%TP DRD502X2.8°8.50mm3.00″16.50mm13.00″46″80g300cpm40T.30T, Kevlar, 3K Fiber
KGTP65+ D40KEVLAR LAUNCH TP DRLOW57.00%TP DRD40X3.0°8.50mm3.00″16.10mm13.00″46″74g280cpm40T.30T, Kevlar, 3K Fiber
KGTP65+ D30KEVLAR LAUNCH TP DRLOW57.00%TP DRD30S3.0°8.50mm3.00″16.00mm13.00″46″72g265cpm40T.30T, Kevlar, 3K Fiber

1. FREQUENCY Measurement Array Parameters: 4.5″ clamp as follows:

ShaftClub LengthHead Mass Estimate:Shaft LengthChuck WT.Insert Depth
Driver45.00″+/-1.50″200g +/-5g46.00″205g1.00″

Fitting

MODEL#/ SKU:Flex Code (FLEX)Low RangeDRIVER SwingSpeed Fit Baseline +/- 6MPHHigh Range
KGTP65+ D50D50(2X)123+mph129mph+++mph
KGTP65+ D40D40(X)113mph119mph125mph
KGTP65+ D30D30(S)105mph110mph115mph
KEVLAR LAUNCH TOUR SERIES DRIVER MODEL#KGTP65+ D

Elastically Tailored Composites
PURE KINETIC ENERGY
Wound…Rolled…Round…Epic…

Filament Wound, Table Rolled and Vacuum Cured, for an explosive transfer of kinetic energy….
however you drive it, KINETIXX® IMRT will optimize down range distance and target performance.

An active shaft that increases in frequency the greater the force applied.

This hard kicking, elastically tailored composite is engineered to improve club forgiveness and

generate outrageous ball speed and precise shot control!

Technology/Design

Featuring our patented Filament wound and table rolled construction technology combined by vacuum curing to produce a pre-loaded stiff concentric butt to middle quadrant, with an active Table rolled middle quadrant to tip for incomparable stability, dynamic response and feedback.

Kevlar LAUNCH Tour series is Designed for strong players, desiring optimum control and a mid-high incomparable launching shot trajectory, from all driver clubhead Systems.

A highly advanced composite that couples an extraordinary high distribution of mass with a preordained elastic response engineered to optimize swing efficiency and impact mechanics, to benefit launch trajectory and shot performance.

Plays lighter than its static weight due to the demonstrably high balance point, this will contribute to lower built club swing weight.

KGTP65+ D is a multi-material, multi-structure advanced composite shaft that delivers a stout-butt section pre-loaded with a visible fiber structural grid from butt to middle quadrant, coupled with a stout high modulus table rolled Lower quadrant.

Installation Guidelines

Installation Guidelines PADERSON KINETIXX LOADED shafts:

Installation should only be completed by a qualified, trained club builder.

  1. All PADERSON KINETIXx loaded shafts are to be BUTT Cut to length only.
  2. Do not TIP trim any shaft model! Regardless of CPM, or club assembly config.
  3. Please do not Chamfer the tips however light belt abrasion is recommended.
    *Tip preparation: light belt abrasion or hand sanding recommended prior to final assembly.
    *To ensure a smooth and clean build, we perform a post-production tip preparation: 1″ Metalwoods, 1.25″ Irons. depending on hosel bore depth, there will in many assemblies be the need to lightly sand beyond the prepared surface delivered. Light belt abrasion is also recommended to insure a full shaft insert and adequate epoxy adhesion. Do not Chamfer tip section or blade prep (scratch) tip to prepare for epoxy.

Reviews

There are no reviews yet.

Be the first to review “LAUNCH TP”

Your email address will not be published. Required fields are marked *

6 + eleven =

Solve : *
15 − 2 =