VELOCITY

$249.99

Clear
SKU: KVMT60 Categories: ,
Share this product

Description

SPEC DECK
MODEL#/ SKU:Series NameKick PointBalance PointTypeFlex CodeFlex (Equivalent)Torque ±0.5°Tip Dia. ±0.05mmTip/Pal ±0.5″Butt Dia. ±0.12mmButt/Pal ±0.5″Length ±0.1″Weight ±2gFrequency ±5cpmMaterials
KVMT60-D40VELOCITY DRHIGH54.00%STD DRD40X5.3°8.50mm4.00″16.00mm7.50″46″66g255cpm30T,5T Amorphous Nano Carbon
KVMT60-D30+VELOCITY DRHIGH54.00%STD DRD30+S5.5°8.50mm4.00″15.90mm7.50″46″63g245cpm30T,5T Amorphous Nano Carbon
KVMT60-D30VELOCITY DRHIGH52.00%STD DRD30S/R5.7°8.50mm4.00″15.80mm7.50″46″61g235cpm30T,5T Amorphous Nano Carbon
KVMT60-D20VELOCITY DRHIGH52.00%STD DRD20R5.7°8.50mm4.00″15.70mm7.50″46″59g225cpm30T,5T Amorphous Nano Carbon
KVMT60-D15VELOCITY DRHIGH50.00%STD DRD15A5.7°8.50mm4.00″15.30mm7.50″46″57g215cpm30T,5T Amorphous Nano Carbon
KVMT60-D10VELOCITY DRHIGH50.00%STD DRD10LTE6.0°8.50mm4.00″15.20mm7.50″46″54g205cpm30T,5T Amorphous Nano Carbon

1. FREQUENCY Measurement Array Parameters: 4.5″ clamp as folHIGHs:

ShaftClub LengthHead Mass Estimate:Shaft LengthChuck WT.Insert Depth
Driver45.00″+/-1.50″200g +/-5g46.00″205g1.00″

Fitting

MODEL#/ SKU:Flex Code (FLEX)Low RangeDRIVER SwingSpeed Fit Baseline +/- 8MPHHigh Range
KVMT60-D40D40(X)107mph115mph123mph
KVMT60-D30+D30+(S)92mph100mph108mph
KVMT60-D30D30(S/R)87mph95mph103mph
KVMT60-D20D20(R)77mph85mph93mph
KVMT60-D15D15(A)67mph75mph83mph
KVMT60-D10D10(LTE)62mph70mph78mph
VACUUM CURED AMORPHOUS VELOCITY MODEL#KVMT60-D

Elastically Tailored Composites
PURE KINETIC ENERGY
The confluence of materials and craftsmanship

Technology/Design

Featuring Dual-flex reactive technology, in the worlds only pre-loaded and vacuum cured Nano-Carbon amorphous fiber material shaft construction, table rolled laminate composite.

Vacuum Cured to minimize resin content, optimizing elastic strength and dynamic recovery properties of the Nano-Carbon Amorphous material. Enhancing feedback and delivering an extraordinarily flexible and forgiving shaft.

Active butt and tip quadrants tailored for players desiring to improve efficiency and increase ball velocity, through the purest kinetic energy transfer from golfer to club.

KVMT60-D is a Mid-Balance point, High-Low Kick point advanced composite shaft that kicks hard and recover’s fast, in tailored sequence from butt to high tip. producing increased ball velocity and Medium-High shot trajectory.

Installation Guidelines

Installation Guidelines PADERSON KINETIXX LOADED shafts:

Installation should only be completed by a qualified, trained club builder.

  1. All PADERSON KINETIXx loaded shafts are to be BUTT Cut to length only.
  2. Do not TIP trim any shaft model! Regardless of CPM, or club assembly config.
  3. Please do not Chamfer the tips however light belt abrasion is recommended.
    *Tip preparation: light belt abrasion or hand sanding recommended prior to final assembly.
    *To ensure a smooth and clean build, we perform a post-production tip preparation: 1″ Metalwoods, 1.25″ Irons. depending on hosel bore depth, there will in many assemblies be the need to lightly sand beyond the prepared surface delivered. Light belt abrasion is also recommended to insure a full shaft insert and adequate epoxy adhesion. Do not Chamfer tip section or blade prep (scratch) tip to prepare for epoxy.

Reviews

There are no reviews yet.

Be the first to review “VELOCITY”

Your email address will not be published. Required fields are marked *

seventeen − 9 =

Solve : *
17 − 15 =