VELOCITY70 GREEN LD

$249.99

Clear
SKU: KVMT70 Categories: ,
Share this product

Description

SPEC DECK
MODEL#/ SKU:Series NameKick PointBalance PointTypeFlex CodeFlex (Equivalent)Torque ±0.5°Tip Dia. ±0.05mmTip/Pal ±0.5″Butt Dia. ±0.12mmButt/Pal ±0.5″Length ±0.1″Weight ±2gFrequency ±5cpmMaterials
KVMT70-GRNLD60VELOCITY LITE LDHIGH54.00%LDLD60XXX5.5°8.50mm4.00″16.20mm9.50″48″73g275cpm30T,5T Amorphous
KVMT70-GRNLD50VELOCITY LITE LDHIGH54.00%LDLD50XX5.5°8.50mm4.00″16.00mm9.50″48″68g265cpm30T,5T Amorphous
KVMT70-LD30+VELOCITY LITE LDHIGH53.00%LDLD30+S5.7°8.50mm4.00″15.80mm9.50″48″63g245cpm30T,5T Amorphous
KVMT70-LD20VELOCITY LITE LDHIGH51.00%LDD20R5.9°8.50mm4.00″15.70mm9.50″48″60g225cpm30T,5T Amorphous

1. FREQUENCY Measurement Array Parameters: 4.5″ clamp as follows:

ShaftClub LengthHead Mass Estimate:Shaft LengthChuck WT.Insert Depth
Long Driver48.00″200g +/-5g48.00″205g1.00″

Fitting

MODEL#/ SKU:Flex Code (FLEX)Low RangeDRIVER SwingSpeed Fit Baseline +/- 9MPHHigh Range
KVMT70-GRNLD60LD60(XXX)137mph146mph155mph
KVMT70-GRNLD50LD50(XX)127mph135mph143mph
KVMT70-LD30+LD30+(S)92mph100mph108mph
KVMT70-LD20LD20(R)77mph85mph93mph
VACUUM CURED AMORPHOUS VELOCITY SERIES LONG DRIVE SHAFT MODEL#KVMT70-GRNLD

Elastically Tailored Composites
PURE KINETIC ENERGY
The confluence of materials and craftsmanship

Technology/Design

Featuring Dual-flex reactive technology, in the worlds only pre-loaded and vacuum cured Nano-Carbon amorphous fiber material shaft construction, table rolled laminate composite.

Vacuum Cured to minimize resin content, optimizing elastic strength and dynamic recovery properties of the Nano-Carbon Amorphous material. Enhancing feedback and delivering an extremely forgiving shaft.

Active butt and tip quadrants tailored for high speed long drive athletes desiring to improve efficiency and increase ball velocity, through the purest kinetic energy transfer from golfer to club.

KVMT70-LD is a Mid-High Balance point, High kick point advanced composite table rolled construction, that kicks hard and recover’s fast, in tailored sequence from butt to high tip.

Producing increased ball velocity and a Medium height piercing shot trajectory.

Installation Guidelines

Installation Guidelines PADERSON KINETIXX LOADED shafts:

Installation should only be completed by a qualified, trained club builder.

  1. All PADERSON KINETIXx loaded shafts are to be BUTT Cut to length only.
  2. Do not TIP trim any shaft model! Regardless of CPM, or club assembly config.
  3. Please do not Chamfer the tips however light belt abrasion is recommended.
    *Tip preparation: light belt abrasion or hand sanding recommended prior to final assembly.
    *To ensure a smooth and clean build, we perform a post-production tip preparation: 1″ Metalwoods, 1.25″ Irons. depending on hosel bore depth, there will in many assemblies be the need to lightly sand beyond the prepared surface delivered. Light belt abrasion is also recommended to insure a full shaft insert and adequate epoxy adhesion. Do not Chamfer tip section or blade prep (scratch) tip to prepare for epoxy.

Reviews

There are no reviews yet.

Be the first to review “VELOCITY70 GREEN LD”

Your email address will not be published. Required fields are marked *

five × 1 =

Solve : *
24 − 17 =